香蕉视频下载

慢走絲工作原理

慢走絲工作原理：

       慢走絲是利用連續移動的細金屬絲（稱為電極絲，一般為銅絲）作電極，對工件進行脈沖火花放電，產生6000度以上高溫，蝕除金屬、切割成工件的一種數控加工機床。慢走絲加工原理是在線電極與工件之間存在的有縫間隙，持續放電去除金屬的現象。

       由于慢走絲線切割機是采取線電極連續供絲的方式，即線電極在運動過程中完成加工，因此即使線電極發生損耗，也能連續地予以補充，故能提高零件加工精度。慢走絲線切割機所加工的工件表面粗糙度通常可達到Ra=0.8μm及以上，且慢走絲線切割機的圓度誤差、直線誤差和尺寸誤差都較快走絲線切割機好很多，所以在加工高精度零件時，慢走絲線切割機得到了廣泛應用。除了早期的中小型企業，在諸如航空，汽車，醫療等大型企業的加工工廠內也極為常見。